Flrig v1.4.3 now available

The FLdigi development team led by W1HKJ have announced the release of Flrig v1.4.3.  Flrig is a transceiver control program designed to be used either stand alone or as an adjunct to Fldigi.

As with all of the FL suite, Flrig supports PowerPC, Intel (i386) and Apple Silicon (M1) processors with individual downloads available for each architecture. Download the latest version of Flrig here. 

Version 1.4.3 – Maintenance release

    cwio accu_sleep
      * replace milliSleep with new accu_sleep function
      * change activated state of configuration items based on
        port selection
      * change loop timing to use global accu_sleep

    A2B freq only
      * add shift-click to A->B button to transfer only
        frequency from vfoA to vfoB
      * add control-click to A->B button to transfer only
        frequency for vfoB to vfoA

    vfo adjust
      * change increment to fractional values

    start/exit set clock
      * add user configurable commands on program
        . start - immediately after normal start up
        . exit - immediately after normal exit
      * add time sychronization if supported by xcvr
        . xcvr clock synchronized to PC clock on next minute
          rollover, to nearest 50 msec.
        . implemented for these transceiver:
          - ic7100, ic7300, ic7600, ic7610,
            ic7700, ic7800, ic7851
          - FT991, FT991A, FTdx10, FTdx101D, FTdx101MP
            FT1200:time only
          - TS990
        . corrected deactivated controls on some supported xcvrs

    TX500
      * Add Lab599 TX500 transceiver

    cw generator
      * update to timing intervals for CW generator

    ftdx101d
      * fix table lookups for bandwidth

    FTdx10
      * add as independent transceiver backend
        . shares many identical CAT commands to FTdx101D

    FT1000MP
      * correct read vfo A/B conversion logic

    cw invert
      * allow user to specify DTR/RTS either normal (+) or
        inverted(-) signaling.

    Power control
      * change to floating point control to allow for
        fractional changes in power level, i.e. 0.1 W / step

    elad
      * Add ELAD FDM-DUO qrp transceiver

    g90 cw/power/swr
      * set CW/CWR tuning sense
      * update power/swr methods

    K3 power level
      * add OM; read for power level min/max/step initialization

    Disable Polling
      * USE to test various comms issues between flrig and transceiver
        . allow user to disable polling
        . allow user to disable xmlrpc server

    Transmit meters
      * FT991A reported as not showing power out during transmit cycle

    cmedia/serial port
      * allow both serial port and cmedia devices to be initialized
        during startup

    K3/KX3/KXPA metering
      * correct smeter conversion
      * read KX3 power out when KXPA is in standby mode
      * Add code to read SWR from KXPA if active
        . note: the KXPA100 programmers guide
      * Add get trace for KXPA swr reads

    IC7851/9610/9700
      * Change get/set vfoA/B to use x25, x26 command strings
      * correct set/get bandwidth by mode/data/filter

    KX3 ptt/if-shift
      * add get_PTT
      * add reset IF shift control based on current mode
      * add has_ptt_control as test for get_PTT call
      * poll for change in KXPA presence with poll of
        power level setting.  Perform test during both Rx and Tx status

    kx3_options
      * use GET OPTIONS to discover KXPA100 presence

    kx3 extras
      * add programmed support for KXPA


Source: readme.txt, updated 2021-11-14